Rancang Bangun Alat Suction Pump Berbasis Arduino Uno Dilengkapi Dengan Indikator Volume Maksimal Cairan Dalam Tabung

Authors

  • Putu Desta Adi Mandalika Universitas Bali Internasional
  • I Kadek Agus Riki Gunawan Universitas Bali Internasional
  • Putu Vierda Lya Suandari Universitas Bali Internasional

DOI:

https://doi.org/10.31598/jurnalresistor.v5i2.1182

Keywords:

Suction pump, Pressure, Liquid, arduino uno

Abstract

Suction Pump is a medical device with category of life support, to assist medical personnel to suck patient fluids such as mucus, blood, saliva, pus etcetera. The operasional problem are occurs that the amount of liquid sucked exceed the capacity of the liquid tube, so then the liquid will enter the motor.  The motor that is exposed with liquid will be damaged, so it cannot be operated.  The researcher is designed a suction pump based on arduino uno equipped with an indicator of the maximum volume of liquid in the tube, with the addition of a pressure sensor MPXV4115VC6U as a reader of the pressure value of the motor, as well as an Infrared sensor as a detector to determine the amount liquid that enter to the tube. LED and infrared photodiode will trigger the relay to stop the motor automatically when volume of the tube is already full. The method used is an observational - experimental study.  The pressure test results of the suction pump have three data variant. There are 10, 13 and 15 kPa.  The 10 kPa pressure test has an error value of 0.1% then at 13 kPa the error value is 0.1% and 15 kPa has an error value of 0.1%.  The experiment are done and repeated ten times, to check whether the suction pump will turn off automatically.  All experiments were done successfully.

Downloads

Download data is not yet available.

References

Akbar Tanjung. 2015. “Aplikasi Liquid Crystal Display (LCD) 16x2 sebagai Tampilan pada Coconut Milk Auto Machine” Palembang: Politeknik Negeri Sriwijaya.

Avelia, Bertha., Ardiana, Putu Agus. 2016. “Persepsi Investor Sebagai Pemoderasi Pengaruh Profitabilitas Pada Respon Pasar” dalam jurnal E-Jurnal Akuntansi Universitas Udayana.14.3, ISSN: 2302-8559. Badung: Universitas Udayana.

Canon, Lee hamongan Marpaung. 2018. “Rancang Bangun Alat Monitoring Ketinggian Cairan Infus Menggunakan Arduino UNO”. Medan: Universitas Medan Area

Chindy Violetas.S. 2018. “Automatic Suction Pump Dilengkapi Safety Berbasis Arduino”. Jakarta: Politeknik Kesehatan Kementerian Kesehatan Jakarta II.

Daputra, Hendri. 2009. “Calibration Of Suction Pump Instrument To Reference OF BS-EN 837--ISO 17025 2005 ”. Surabaya : Badan Pengaman Fasilitas Kesehatan

Fahim Umar Djawas, Tri Bowo Indrato, M. Ridha Makruf. 2018. “Automatic Suction Pump Continous dilengkapi Safety berbasis Mikrokontroler”. Surabaya: Politeknik Kesehatan Kementerian Kesehatan Surabaya.

Helena Da Fonseca Ximenes. 2018. “alat Pendeteksi Level Cairan Infuse menggunakan Sensor Infra red dan Photodioda berbasis Text Short Message”. Yogyakarta: Universitas Muhammadiyah Yogyakarta.

Nia Pramitasi. 2019. “Perbandingan Tindakan Suction Endotracheal Dengan Menggunakan Tekanan 20 kPa dan 25 kPa Terhadap penurunan Saturasi oksigen di Ruang Intesive Care Unit RSUD Prof. Dr. Margono Soekarno Purwokerjo”. Purwokerto: Universitas Muhammadiyah Purwokerto.

Khusna, Asmaul. 2017. “Studi Kualitas Air Sungai Sudimoro Di Mojokerto Berdasarkan Indeks Keanekaragaman Makrozoobentos Sebagai Sumber Belajar Biologi” (skripsi). Malang: Universitas Muhammadiyah Malang.

Sapto, Hudha pratama. 2015. “RFID sebagai Pengaman Pintu Laboratorium Jurusan Teknik elektro”. Semarang: Universitas Negeri Semarang.

Viralia, maulina Puspasari. 2018. “Modifikasi Suction Pump Dilengkapi Safety Cairan”. Yogyakarta: Universitas Muhammadiyah Yogyakarta.

Viska Miftakhul Jannah. 2019. “Pengaruh Tekanan negative Suction Terhadap Perubahan Saturasi oksigen pada Pasien Terpasang Ventilasi Mekanik di Ruang Intesive care unit (ICU) RSUD K.M.R.T Wongsonegoro Kota Semarang”. Semarang: Politeknik Kesehatan Kementerian Kesehatan Semarang.

Downloads

Published

2022-10-28

How to Cite

Adi Mandalika, P. D., Gunawan, . I. K. A. R., & Suandari, P. V. L. (2022). Rancang Bangun Alat Suction Pump Berbasis Arduino Uno Dilengkapi Dengan Indikator Volume Maksimal Cairan Dalam Tabung. Jurnal RESISTOR (Rekayasa Sistem Komputer), 5(2), 168-173. https://doi.org/10.31598/jurnalresistor.v5i2.1182